Ready for Revo

Change nozzles at room temperature using just your fingers. No complex tools, no hot tightening. Revo Nozzles are factory sealed nozzle and heatbreak in one, so they’re easy to fit and can’t leak material when in use.

Titanium-like performance

E3D's special manufacturing process gives this aluminum HotEnd the strength and low thermal conductivity of titanium, without actually being titanium!

New hotness

A Revo HeaterCore heats up in seconds. It’s much safer too – unlike other solutions on the market, a positive temperature coefficient (PTC) means the Revo HeaterCore can not melt at extreme temperatures: power reduces as it gets hotter, so hazards are reduced in the event of a thermal runaway.

Runs cool, looks cool

With an anodized red, blue, or grey heatsink, not only does Revo Voron run cool – it looks cool, too. 

Flexible to any setup

Revo Voron is intended for Voron printheads. All heatercore options are manufactured by E3D, but the "LDO version" has different cable length and terminations, intended for use with their toolhead boards but may be useful with other boards as well. Check the drawing for details.

Key features

• Low thermal conductivity in a compact space
• Maximum temperature: 300C
• Lightweight for greater motion system agility
• Compatible with RapidChange Revo ecosystem
• 4x M3 mounting style (see drawing)
  
• Compatible with direct drive systems
• Mass: 25g

Kit Contains

Revo Voron HeatSink with integrated PZ Probe (piezo sensor + PCB)
Revo HeaterCore w/ spring & connectors (see drawing for details)
1 meter Microfit to Dupont cables (if E3D edition Heatercore is selected)
No mounting hardware included
Plus:

Minimal kit:

- 1 x 0.40mm brass Standard Flow Revo Nozzle

Starter:
- 1 x 0.40, 0.60 brass Standard Flow Revo Nozzles

Fully loaded nozzle kit:
- 1 x 0.25, 0.40, 0.60, and 0.80mm brass Standard Flow Revo Nozzles

High flow kit:
- 1 x 0.40mm brass Standard Flow Revo Nozzle
- 1 x 0.40mm brass High Flow Revo Nozzle
- 1 x 0.60mm brass High Flow Revo Nozzle
- 1 x Fully Loaded sock kit

High flow X kit:
- 1 x 0.40mm brass Standard Flow Revo Nozzle
- 1 x 0.40mm ObXidian High Flow Revo Nozzle
- 1 x 0.60mm ObXidian High Flow Revo Nozzle
- 1 x Fully Loaded sock kit

High flow X kit:
- 1 x 0.40mm brass Standard Flow Revo Nozzle
- 1 x 0.40mm ObXidian High Flow Revo Nozzle
- 1 x 0.60mm ObXidian High Flow Revo Nozzle
- 1 x Fully Loaded sock kit

Genius kit:
- 1 x 0.25mm brass Standard Flow Revo Nozzle
- 1 x 0.40mm brass non-planar/belt Revo Nozzle
- 1 x 0.40mm ObXidian Revo Nozzle
- 1 x 0.60mm ObXidian High Flow Revo Nozzle
- 1 x 0.60mm High Temperature Abrasive Revo Nozzle
- 1 x Fully Loaded sock kit
- 1 x Revo Heaterblock
- 1 x High Precision Heater Cartridge, 24v/40w
- 1 x PT100 or PT1000 temperature sensor

Genius metal kit:
- 1 x 0.25mm brass Standard Flow Revo Nozzle
- 1 x 0.40mm brass non-planar/belt Revo Nozzle
- 1 x 0.40mm ObXidian Revo Nozzle
- 1 x 0.60mm ObXidian High Flow Revo Nozzle
- 1 x 0.60mm High Temperature Abrasive Revo Nozzle
- 1 x Fully Loaded sock kit
- 1 x Revo Heaterblock
- 1 x High Precision Heater Cartridge, 24v/40w
- 1 x PT100 or PT1000 temperature sensor
- 1 x 0.4mm Diamondback nozzle

FAQs:

• Which heatercore do I need? -> 99%+ of Vorons are 24v. All heatercores are made by E3D, but the LDO edition comes with different cable lengths/terminations. See drawing for details. As far as 40w vs 60w, for most use cases, even high flow, 40w is plenty. Unless you have at least 2 of these 3: [extreme part cooling, in excess of 40mm3/s, printing in excess of 275degC], you will not benefit from a 60w heatercore.
• Which nozzles do I need? -> Revo HF increases flow rates by roughly 70% as compared to standard flow. Check out the graph here for more information.